• 產品簡介
• 圖片展示

PRODUCT FEATURES: 產品特征：

LXBX series ultra-low temperature separator machine is a

high-tech product which was independently designed and

developed by Lixang Refrigeration Equipment Co., Ltd.

LXBX系列超低溫分離機是由立翔制冷設備有限公司自主設計開發的高科技產品。

It is very suitable for various sizes of mobile phones' LCD repair, recycling, refurbishment, rework, etc.

其非常適合各種規格的手機LCD屏維修、回收、翻新、返工等”。

 The lowest temperature of the machine can reach up to -180℃ without using liquid Nitrogen as refrigerant.

在不使用液氮作制冷劑的情況下，機器工作區域的最低溫度可達到-180℃.

 It can easily separate out glass, TP, back-light, OCA, LOCA,bracket from damaged LCD module. No need to change the polarizer film.

它可以很容易地將玻璃、TP、背光、OCA膠、LOCA膠、支架等從損壞的液晶模組中分離出來, 不需要更換偏光片。

 High efficiency. No components damage during the LCD module separating process.

高效，并且在液晶模組分離過程中沒有元件損壞。

 It is really a good helper for the LCD reparation industry.

它確實是液晶顯示器修復行業的一個好幫手。

Operation Instructions: 操作說明

 1.) Before using, it will take the machine around 30～40 minutes to

cool to the set working temperature.

使用前，需要在30~40分鐘左右將機器冷卻至設定的工作溫度。

 2.) Place the LCD screen on the frozen plate.

將液晶屏放置在冷凍板上。

 3.) Freezing time from 30 seconds to 1 minute depends on different LCD screens.

冷凍時間從30秒到1分鐘取決于不同類型的液晶屏幕。

 4.) Take out LCD screen and separate it.

取出液晶屏并將其分離開。

5.) Below is the URL of youtube video link for your reference:

以下是優酷視頻鏈接的URL，供您參考：

http://i.youku.com/i/UMzYwNzc0OTg4NA==?spm=a2hzp.8244740.0.0

Tips: 提示

 1. For serious crushed glass, please stick a tape on glass for safety and good for machine.

對于嚴重的碎玻璃，請用膠帶貼在玻璃上，以保證安全，對機器也有好處。

 2. Please make sure the operator wears gloves in case of danger.

請確保操作員戴上手套，以防止危險，

 3. It is much easier to separate out the bracket and other components after freezing processing. Please pay attention to the back-light water inlet.

經過冷凍處理后，分離支架和其他部件要容易得多。請注意背光水口。

 4. After separating the LCD screen, pay attention to the water treatment and temperature recovery.

液晶屏分離后，注意水的處理和溫度的回收。

 5. When separating the curved screen, the separation risk caused by the temperature difference between 2 sides of the curved surface

LCD screen. Please pay more attention to this point.

分離曲面屏時，曲面LCD屏幕兩側溫差引起的分離風險，請注意到這一點。

 6. After LCD separation, please put the glue side upward to avoid sticking on the article surface after the temperature return to the normal.

液晶屏分離后，請將屏的膠水側向上放置，以避免雜物粘在屏表面后，并讓屏的表面溫度恢復正常。

Product Parameters: